subject
Physics, 02.12.2021 01:50 mattgraham366

1. Plot a velocity-time graph using table: Draw a line of the best fit and use your graph to find:

° Acceleration during the first 4 seconds
° The distance traveled in the first 4 seconds;

 The distance traveled in the first 5 seconds;

 The average speed during the 8 seconds of motion shown.

2. The diagram below shows a block of wood on a sloping surface. Copy the

diagram and label all the forces that act on the block of wood.

3. A spring stretches from 10 cm to 22 cm when a force of 4 N is applied. If it

obeys Hooke’s law, find its total length in cm when a force of 6 N is applied.

4. A rocket has a mass of 500 kg.

 What is its weight on Earth, if g = 10 N/kg?

 At lift-off the rocket engine exerts an upward force of 25 000 N. What is the

resultant force on the rocket?

 What is its initial acceleration?

5. A ball is projected vertically upwards with an initial velocity of 30 m/s. Find its

maximum height and the time taken to return to its starting point. Neglect air

resistance and take g = 10 m/s2

.(Hint: the velocity of the ball is zero at its highest point.)

GIVE ME THE REAL ANSWER ALREADY AND I WILL BE VERY HAPPY!

AND DON'T GIVE ME THE LINK DESCRIPTION! UNDERSTAND!


1. Plot a velocity-time graph using table:

Draw a line of the best fit and use your graph to find

ansver
Answers: 2

Another question on Physics

question
Physics, 22.06.2019 03:30
As part of an industrial process, air as an ideal gas at 10 bar, 400k expands at steady state through a valve to a pressure of 4 bar. the mass flow rate of air is 0.5 kg/s. the air then passes through a heat exchanger where it is cooled to a temperature of 295k with negligible change in pressure. the valve can be modeled as a throttling process, and kinetic and potential energy effects can be neglected. (a) for a control volume enclosing the valve and heat exchanger and enough of the local surroundings that the heat transfer occurs at the ambient temperature of 295 k, determine the rate of entropy production, in kw/k. (b) if the expansion valve were replaced by an adiabatic turbine operating isentropically, what would be the entropy production? compare the results of parts (a) and (b) and discuss.
Answers: 3
question
Physics, 22.06.2019 10:30
Agroup of students were investigating the force of gravity. they began by dropping a foam ball from a height of 3 meters into a bucket of sand. the ball hit the sand in 0.306 seconds. they dropped additional balls of approximately the same diameter, but of different masses. here is the data they collected. based on this experiment and the collected data, what would their conclusion be?
Answers: 1
question
Physics, 22.06.2019 17:00
If you wanted to move an electron from the positive to the negative terminal of the battery, how much work w would you need to do on the electron? enter your answer numerically in joules.
Answers: 1
question
Physics, 22.06.2019 21:40
Engines for propeller-driven aircraft are limited in their maximum rotational speed by the fact that the tip speed of the propeller must not approach the speed of sound in air (mach i). taking 6 ft as a typical diameter for a propeller of a light airplane and 1100 fils as the speed of sound, find the upper limit on the rpm (revolutions per minute) of the propeller shaft.
Answers: 3
You know the right answer?
1. Plot a velocity-time graph using table: Draw a line of the best fit and use your graph to find:...
Questions
question
Mathematics, 12.04.2021 02:40
question
Mathematics, 12.04.2021 02:40
Questions on the website: 13722362