Engineering, 23.12.2020 23:50 zahwaahmaf

Chapter 19: Diesel Engine Operation and Diagnosis -Chapter Quiz 1. How is diesel fuel ignited in a warm diesel engine?
A. Glow plugs
B. Heat compression
C. Spark plugs
D. Distributor-less ignition system

2. Which type of diesel injection produces less noise?
A. Indirect injection (IDI)
B. Common rail
C. Direct injection
D. Distributor injection

3. Which diesel injection system requires the use of a glow plug?
A. Indirect injection (IDI)
B. High pressure common rail
C. Direct injection
D. Distributor injection

4. The three phases of diesel ignition include .
A. Glow plug ignition, fast burn, slow burn
B. Slow burn, fast burn, slow burn
C. Ignition delay, repaid combustion, controlled combustion
D. Glow plug ignition, ignition delay, controlled combustion

5. What fuel system component is used in a vehicle equipped with a diesel engine that is seldom used on the same vehicle when it is equipped with a gasoline engine?
A. Fuel filter
B. Fuel supply line
C. Fuel return line
D. Water-fuel separator

6. The diesel injection pump is usually driven by a .
A. Gear off the camshaft
B. Belt off the crankshaft
C. Shaft drive off of the crankshaft
D. Chain drive off of the camshaft

7. Which diesel system supplies high-pressure diesel fuel to all the injectors all of the time?
A. Distributor
B. Inline
C. High-pressure common rail
D. Rotary

8. Glow plugs should have high resistance when and lower resistance when .
A. Cold/warm
B. Warm/cold
C. Wet/dry
D. Dry/wet

9. Technician A says that glow plugs are used to help start a diesel engine and are shut off as soon as the engine starts. Technician B says that the glow plugs are turned off as soon as a flame is detected in the combustion chamber. Which Technician is correct?
A. Technician A only
B. Technician B only
C. Both Technicians A and B
D. Neither Technicians A NOR B

10. What part should be removed to test cylinder compression on a diesel engine?
A. An injector
B. An intake valve rocker arm and stud
C. An exhaust valve
D. A glow plug

Answers: 3

Show answers

Another question on Engineering

Engineering, 04.07.2019 18:10

Items are similar to the free issue items, but their access is limited. (clo5) a)-bin stock items free issue b)-bin stock controlled issue c)-critical or insurance spares d)-rebuildable spares e)-consumables

Answers: 1

Answer

Engineering, 04.07.2019 18:10

Compute the pressure drop of 30°c air flowing with a mean velocity of 8 m/s in a circular sheet-metal duct 300 mm in diameter and 15 m long. use a friction factor, f 0.02, and pair = 1.1644 kg/m a. 37.26 pa b. 25.27 pa n c. 29.34 pa d. 30.52 pa

Answers: 1

Answer

Engineering, 04.07.2019 19:20

To save energy, the air supply to a 2000 ft office has been shut off overnight and the room temperature has dropped to 40°f. in the morning, the thermostat is reset to 70°f and warm air at 120 f begins to flov in at 200ft'/min. the air is well mixed within the room, and an equal mass flow of air at room temperature (changing with time) is withdrawn through a return duct. the air pressure is nearly 1 atm everywhere. ignoring heat transfer with the surroundings and kinetic and potential energy effects, estimate how long it takes for the room temperature to reach 70°f. plot the room temperature as a function of time.

Answers: 1

Answer

Engineering, 04.07.2019 19:20

Apiping systems consists of 6 m of 6-std type k and 12 m of 4-std type k, both drawn copper tubing. the system conveys ethylene glycol at a rate of 0.013 m3/s. the pressure drop across the system is to be calculated. there are two 90° elbows in the 6-in pipe, a reduction from the 6-in pipe to the 4-in pipe and four 90° elbows in the 4-in pipe. all fittings are soldered (same as flanged) and regular. the inlet and outlet of the system are at the same height.

Answers: 1

Answer

You know the right answer?

Chapter 19: Diesel Engine Operation and Diagnosis -Chapter Quiz 1. How is diesel fuel ignited in a...

Questions