subject

Physics, 09.12.2021 17:00 calvarado12

Consider two identical 3 kW PV systems. The array of one operates at twice the voltage of the other. What are two benefits of this increased voltage

ansver

Answers: 3

Show answers

Another question on Physics

question

Physics, 20.06.2019 18:04

How does mass affect the speed of an object

Answers: 1

question

Physics, 22.06.2019 16:00

Amichelson interferometer operating at a 600 nm wavelength has a 3.02-cm-long glass cell in one arm. to begin, the air is pumped out of the cell and mirror m2 is adjusted to produce a bright spot at the center of the interference pattern. then a valve is opened and air is slowly admitted into the cell. the index of refraction of air at 1.00 atm pressure is 1.00028.how many bright-dark-bright fringe shifts are observed as the cell fills with air?

Answers: 1

question

Physics, 22.06.2019 19:00

What is the gravitational attraction between a dating couple whose centers of mass are 0.630 m apart if the boy weighs 715 n and the girl weighs 465 n?

Answers: 3

question

Physics, 23.06.2019 00:00

If water vapor with the mass of 35.0 grams is cooled and condensed into water in a closed system such as a closed glass jar, what is the mass of the water after the water vapor completely condenses? a) 34.5 grams b) 35.0 grams c) 35.5 grams d) the mass cannot be determined without knowing the volume

Answers: 2

You know the right answer?

Consider two identical 3 kW PV systems. The array of one operates at twice the voltage of the other....

Questions

question

Engineering, 26.07.2019 16:20

Put the four main steps of the injection molding process in correct order. (place the correct step number after the text line) a)- injection of plasti...

question

Engineering, 26.07.2019 16:20

Which dimensionless number can describe the rela boundary layers? umber can describe the relative thickness of the velocity and thermal a. biot b. nu...

question

Engineering, 26.07.2019 16:20

A½ inch diameter bolt is under a shear load of 4500 lb. determine the average shear stress on the bolt. assume the bolt is in single shear and is made...

question

Engineering, 26.07.2019 16:20

The pressure drop is the irreversible pressure loss between the inlet and the exit of a tube bank. a pressure loss has units of a. j 1 b. n c. pa d. w...

question

Engineering, 26.07.2019 16:20

What does the 13 in the ½-13 screw call-out stand for? a. thread pitch (distance between threads) b. major diameter of thread c. threads per inch d....

question

Engineering, 26.07.2019 16:20

The diesel cycle is very close to the otto cycle. what is a difference between the two air-standard cycles? a)-the diesel cycle assumes constant volu...

question

Engineering, 26.07.2019 16:20

One can expect the velocity boundary layer for laminar flow to be much thicker than the thermal boundary layer when the prandtl number is a. > >...

question

Engineering, 26.07.2019 16:20

Select a light w shape for a column subjected to an axial compressive load of 355 kips. the unbraced length of column is 16 ft and the ends are pinned...

question

Engineering, 26.07.2019 16:20

Which has more threads per inch: ¼-20 or an m8-1? a)- ¼-20 b)- м8-1 c)- same...

question

Engineering, 26.07.2019 16:20

Use the map of ohio that follows to find the average wind speed for columbus, ohio (5.5 m/s). a wind turbine located at byers mazda subaru near i 270...

question

Engineering, 26.07.2019 16:20

An a36 - 1.0 inch diameter steel tie rod is used to support a tensile load of 12,000 lb. determine the stress in the tie rod and calculate the factor...

question

Engineering, 26.07.2019 16:20

Afluid in direct contact direct contact with a stationary solid surface will have a velocity of zero in accordance with the condition. a. no-slip b. t...

question

Engineering, 26.07.2019 16:20

Steam enters an adiabatic turbine at 10 mpa and 500 °c and leaves at 30 kpa with a quality of 90 percent. neglecting the changes in kinetic and potent...

question

Engineering, 26.07.2019 16:20

Calculate the bending stress in a 1 ¾ in. x 12 in. x 18 ft. microllam lvl beam under the following load conditions: a)-2500 lb concentrated load at c...

question

Engineering, 26.07.2019 16:20

A) what is a free-cutting steel? explain. b) show the free energy vs. composition curve (schematic) for an alloy system a-b where there is a strong t...

question

Engineering, 26.07.2019 16:20

Acylindrical steel specimen is subjected to a stress of 100 mpa along the longitudinal axis. the undeformed specimen has a diameter do=10 mm and a len...

question

Engineering, 26.07.2019 16:20

What volume of helium is needed if a balloon is to lift a load of 1200kg (including the weight of the empty balloon)?...

question

Engineering, 26.07.2019 16:20

The backyard grill on the deck of a certain thermodynamics instructor, a rigid 0.5 m3 propane tank is left in the sun and gets hot. as a result, the p...

question

Engineering, 26.07.2019 16:20

Hot air flows through a pipe, as shown above. the properties of air may be taken as: k=0.03 w/m-k, pr=0.7, μ=208.2 x 10"n s/m^2 and ρ=0995 kg/m^3. cal...

question

Business, 26.07.2019 16:20

How often should you typically monitor your checking account?...

More questions: Physics Another questions

Questions on the website: 13722367