The dot plot shows how many cats are owned by each person in a neighborhood:
dot plot titled neighborhood cats and labeled number of cats shows number line from 1 to 10. there are 6 dots over 1, 3 dots over 2, 2 dots over 3, 1 dot over 4, 0 dots over 5, 6, 7, 8, and 9, and 1 dot over 10.
is the median or the mean a better measure of center for these data and why?
mean, because the data are skewed and there is an outlier
mean, because the data are symmetric and there are no outliers
median, because the data are skewed and there is an outlier
median, because the data are symmetric and there are no outliers

If we plot the data on the graph, we can see that the data is skewed to the right (positive skew) and there is an outlier. In skewed data and presence of outlier, the median is most commonly used measure of central tendency. This is because a positive skew would result in a positive bias to the mean. Meaning that it would be a lot larger than the median and not really representing the actual central tendency. The median however is less affected by the skew and outliers.

Median, because the data are skewed and there is an outlier

fist on the left goes with the third on the right. second on the left goes with the fourth on the right. third on the left goes with the second on the right. the fourth on the left goes with first on the right

part a

answer: a reasonable domain is where n is a real number. so n can be between 0 and 10. both endpoints are included.

work shown:

n is the number of days after the experiment starts. the smallest n can be is n = 0 which means that 0 days have gone by, and we're at the start. to find out how large n should be, then replace f(n) with 16.13 and solve for n. use logarithms to isolate the exponent.

f(n) = 12*(1.03)^n

16.13 = 12*(1.03)^n

16.13/12 = (1.03)^n

1.34416666666667 = (1.03)^n

(1.03)^n = 1.34416666666667

log[ (1.03)^n ] = log[ 1.34416666666667 ]

n*log[ 1.03 ] = log[ 1.34416666666667 ]

n = log[ 1.34416666666667 ]/log[ 1.03 ]

n = 10.0062999823929

this rounds to n = 10 which is fairly close but not 100% perfect. so this is the largest n can be.

note: if you plug n = 10 into f(n), you'll get roughly 16.127 which rounds to 16.13 (this comes up again in part c)

=====================================

part b

answer: the y intercept is 12. it represents the starting height of the plant in cm.

work shown:

plug n = 0 into the f(n) function. simplify

f(n) = 12*(1.03)^n

f(0) = 12*(1.03)^0

f(0) = 12*(1)

f(0) = 12

on day n = 0, aka the starting point, the height f(n) is 12 cm

=====================================

part c

answer: the average rate of change is approximately 0.43061036458991 (round however you need to). this represents the average growth rate from day n = 3 to day n = 10. so the plant grew roughly 0.43 cm per day during this timespan, assuming you round to 2 decimal places.

work shown:

compute f(3)

f(n) = 12*(1.03)^n

f(3) = 12*(1.03)^3

f(3) = 13.112724 < we'll use this later

compute f(10)

f(n) = 12*(1.03)^n

f(10) = 12*(1.03)^10

f(10) = 16.1269965521294 < we'll use this later

now use the formula below with a = 3 and b = 10

aroc = average rate of change

aroc = [ f(b) - f(a) ]/[ b - a ]

aroc = [ f(10) - f(3) ]/[ 10 - 3 ]

aroc = (16.1269965521294 - 13.112724)/(10 - 3)

aroc = 3.0142725521294/7

aroc = 0.43061036458991

round this however you need to

note: the plant grew approximately 3.01 cm over 7 days, so roughly 0.43 cm per day is the average growth rate (if you were to round to 2 decimal places).