Mathematics, 14.12.2019 21:31 ehaynie

The package of a particular brand of rubber band says that the bands can hold a weight of 7 lbs. suppose that we suspect this might be an overstatement of the breaking weight. so we decide to take a random sample of 36 of these rubber bands and record the weight required to break each of them. the mean breaking weight of our sample of 36 rubber bands is 6.6 lbs. assume that the standard deviation of the breaking weight for the entire population of these rubber bands is 2 lbs. true or false? finding a random sample with a mean this low in a population with mean 7 and standard deviation 2 is very unlikely.

Answers: 1

Show answers

Another question on Mathematics

Mathematics, 21.06.2019 22:00

Asquare and an equilateral triangle have the same perimeter. each side the triangle is 4 inches longer than each side of the square. what is the perimeter of the square

Answers: 1

Answer

Mathematics, 22.06.2019 00:30

If on=8x-8,lm=7x+4,nm=x-5,and ol=3y-6

Answers: 2

Answer

Mathematics, 22.06.2019 01:10

If the diagram polygon abcd is a reflection across ef to make polygon a'b'c'd'.

Answers: 2

Answer

Mathematics, 22.06.2019 01:20

Which of the following shows the graph of y=2e^x?

Answers: 2

Answer

You know the right answer?

The package of a particular brand of rubber band says that the bands can hold a weight of 7 lbs. sup...

Questions

Medicine, 13.09.2019 23:20

The anatomical division of the pharynx that is located behind the mouth from the soft palate above to the level of the hyoid bone below is called the:...

Chemistry, 13.09.2019 23:20

Alarge pot (10 kg) of beef stew is left out on the kitchen counter to cool. the rate of cooling, in kj/min, equals 1.955 (t-25), where t is the temper...

Chemistry, 13.09.2019 23:20

Conversion of mass to moles a continuous feed to a separation unit is 1,000 kg/h of 45 wt% methanol and 55 wt% water, whose molecular weights are 32 a...

Chemistry, 13.09.2019 23:20

Two containers initially contain dry air at 40°c. water is added to both containers so that the relative humidity is 30% in container #1, and 80% in c...

Chemistry, 13.09.2019 23:20

The enthalpy of vaporization of h2o at 1 atm and 100 c is 2259 kj/kg. the heat capacity of liquid water is 4.19 kj/kg-c, and the heat capacity of wate...

Chemistry, 13.09.2019 23:20

Calculate the cell potential for a cell operating with the following reaction at 25 degrees celsius, in which [mno4^1-] = .01m, [br^1-] = .01m, [mn^2+...

Chemistry, 13.09.2019 23:20

An aqueous solution of nazco3 saturates at 300 k to form, nazco3.3h2o crystals. 10 kg/h of 35 mass% aqueous solution enters a continuous evaporative c...

Chemistry, 13.09.2019 23:20

The halpy of vaporization of h2o at 1 atm and 100 c is 2259 kj/kg. the heat capacity of liquid water is 4.19 kj/kg. c, and the heat capacity of water...

Chemistry, 13.09.2019 23:20

Prepare benzoic acid from benzyl alcohol.5 ml of sodium hydroxide, water and potassium manganese are added. how could you tell when the reaction...

Mathematics, 13.09.2019 23:20

When given a graph, the vertical line test can be used to determine functionality. describe the vertical line test and explain the reasons why a graph...

Engineering, 13.09.2019 23:20

Two factors that can be modified to optimize the cutting processes are feed and depth, and cutting velocity. a) true b) false...

Engineering, 13.09.2019 23:20

The highest cutting temperature is located close to the shear zone. a) true b) false...

Engineering, 13.09.2019 23:20

The largest source of heat generated in metal cutting is due to friction. a) true b) false...

Engineering, 13.09.2019 23:20

Calculate the differential pressure in kpa across the hatch of a submarine 320m below the surface of the sea. assume the atmospheric pressure at the s...

Engineering, 13.09.2019 23:20

Increasing rake angle will decrease the tendency for built-up-edge to form. a) true b) false...

Engineering, 13.09.2019 23:20

An orthogonal cutting operation is performed using a rake angle of 15°, to=0.012 in and w=0.100 in. the chip thickness ratio is measured after the cut...

Engineering, 13.09.2019 23:20

Write the type of chips generated at each of the following cutting conditions, and explain why. a. low cutting speed: b. large depth of cut: c. very...

Engineering, 13.09.2019 23:20

How are the polymeric materials classified? give examples of the plastic materials and elastomers? give the difference between thermoplastics and t...

Engineering, 13.09.2019 23:20

What is components? what is phases? what is tie line?...

Engineering, 13.09.2019 23:20

Avariable speed reciprocating compressor of mass 400 kg has a natural frequency of 16.2 hz. (a) design an optimum auxiliary mass damper, so that the m...

More questions: Mathematics Another questions